Renewable energy

Renewable energy
Biofuels Biomass Hydro power Geothermal power Solar power Tidal power Wave power Wind power
Alternative energy

The wind, sun, and biomass are three renewable energy sources.

Burbo Bank Offshore Wind Farm, at the entrance to the River Mersey in North West England.

Renewable energy is a term for any useable energy that is harnessed from natural resources that are either essentially inexhaustible (such as sunlight, or thermal energy generated and stored in the Earth) or naturally replenished in a timely manner on a human timescale (such as energy derived from wood). In contrast, non-renewable energy refers to energy derived from resources that are limited in amount and cannot be replenished in a a timely manner or feasibly and are essentially irreplaceable once extracted (such as energy derived from fossil fuels). The term renewable energy has not only been applied to the energy and forms of energy harnessed but also to the sources and technologies associated with that useable energy. Examples of renewable energy technologies include methods to harness water power, sunlight, thermal energy, or biomass for the generation of electricity.

The term renewable energy is often used interchangeable with alternative energy and green energy. While by most definitions there is substantial overlap between energy forms, sources, and technologies that fit into these three categories, the three terms also have been delineated differently. The term alternative energy generally references any nontraditional energy form, source, or technology differing from the current popular forms, sources, or technologies. Before natural gas gained popularity, this energy source could be classified under the category of alternative energy; however, it does not fit under renewable energy. Green energy references that subset of renewable energy that involves the least environmental harm.

Definitions and scope

There are a multitude of definitions used for renewable energy. The various conceptions allow debate regarding what is included in this category, whether energy from peat, large hydropower plants, or biomass are counted as renewable energies, and whether one includes nuclear power.

A commonly cited definition is that provided by the International Energy Agency (IEA 2008):

"Renewable energy is derived from natural processes that are replenished constantly. In its various forms, it derives directly or indirectly from the sun, or from heat generated deep within the earth. Included in the definition is energy generated from solar, wind, biomass, geothermal, hydropower and ocean resources, and biofuels and hydrogen derived from renewable resources."

This definition is used by the United Nations Environment Programme (UNEP 2011). The IEA website references a similar but differently worded version: "Energy derived from natural processes (e.g. sunlight and wind) that are replenished at a faster rate than they are consumed. Solar, wind, geothermal, hydro, and some forms of biomass are common sources of renewable energy" (IEA 2014).

A panoramic view of the Whitelee Wind Farm with Lochgoin Reservoir in the foreground.

A definition used by the European Union utilizes this conception: "Renewable energy sources are defined as renewable non-fossil energy sources: wind, solar, geothermal, wave, tidal, hydropower, biomass, landfill gas, sewage treatment plant gas and biogases" (Gritsevskyi 2008).

The German Renewable Energy Act (Erneuerbare-Energien-Gesetz or EEG) delineates what fits into the renewable energy category as "hydropower including wave power, tidal power, salt gradient and flow energy, wind energy, solar radiation, geothermal energy, energy from biomass including biogas, landfill gas and sewage treatment plant gas, as well as the biodegradable fraction of municipal and industrial waste." Not included within this definition is biomass from non-biodegradable plants nor large hydropower plants (Jordan-Korte 2011).

Michael Hoexter offers this analysis: "Non-renewable energy sources are energy stores with zero or a minute rate of replenishment relative to its depletion by human beings" and "renewable energy sources are types of natural energy flux useful for human ends regularly occurring on or near Earth's surface and, additionally, useful natural energy stores that are replenished by natural flux within the time frame of conceivable human use." Hoexter further "all known renewable energy sources originate in, or are close derivatives of, electromagnetic radiation of our Sun, the Earth's and Moon's gravitational fields, and heat radiating from Earth's interior (Gritsevskyi 2008).

Whether a particular resources serves as a source of renewable energy is often a point of contention. Some countries, such as Sweden and Finland, label peat as a renewable source of energy, while the World Energy Council (WEC) suggests to not consider peat a renewable source of energy. (Gritsevskyi 2008). Peat has a notably slow and low renewable rate. Some US and UK politicians have termed nuclear power a renewable energy (Jordan-Koret 2011), and physicist Bernard Cohen has stated that uranium is "practically inexhaustible" and can be considered a renewable course of energy, with naturally-replenished uranium extracted from seawater able to supply energy as long as the sun's expected lifespan (Gritsevskyi 2008). Other have advocated against inclusion of nuclear energy ((Jordan-Koret 2011) and some has even questioned geothermal since it may lead to partial depletion at some locales (Gritsevskyi 2008).

The term renewable energy—forms, technologies, and sources—is distinct from the term renewable natural resource in that this later term generally also includes resources from which useable energy is not obtained, such as fish stocks or wildlife (and non-renewable resources include minerals, such as gold, silver, diamonds, and copper). An energy source, according to IEA/Eurostat definition is "the kinetic (e.g. hydro, wind), thermal (eg. nuclear, geothermal), or combustible fuel used as the input to generate electricity or heat" (Gritsevskyi 2008). Energy inside a system is transformed from one energy form to another (thermal to electricity), and an energy technology is that which transforms, transports, or stores the energy form.

Overview

In 2010 renewable energy accounted for 17% of total energy consumption. Biomass heat accounted for 11%, and hydropower 3%

In 2010, renewable energy provided an estimated 16.7% of global final energy consumption, according to the Renewable Energy Policy Network for the 21st Century (REN21). About 8.5% of this came from traditional biomass and about 8.2% came from modern renewable energy (hydropower, solar, wind, geothermal, biofuels, modern biomass). Hydropower accounted for about 3.3% of global final energy consumption in 2010 (REN21 2012).

Global renewable power capacity excluding hydro.

The International Energy Agency (IEA) reported that in 2010 the use of renewable energy (including traditional biomass) accounted for about 13% of global primary energy demand (IEA 2012) and in 2009 renewables accounted for 19.5% of global electricity generation (IEA 2014). Bloomberg (2011) reported that renewable sources, including large hydro, had a 12.6% share of total primary energy production in 2010.

At the national level, by 2013 at least 30 nations around the world had renewable energy contributing more than 20% of energy supply. National renewable energy markets are projected to continue to grow strongly in the coming decade and beyond (REN21 2013). Wind power, for example, is growing at the rate of 30% annually, with a worldwide installed capacity of 282,482 megawatts (MW) at the end of 2012.

In the United States, renewable energy sources were used in 2012 to provide abut 12% of total U.S. utility-scale electricity generation, mostly from hydroelectic power (56%), followed by wind (28%), biomass wood (8%), biomass waste (4%), geothermal (3%), and solar (1%) (EIA 2013). The top nations in terms of total electricity generation from renewable energy, in order, are China, United States, Brazil, and Canada, while the order for production of electricity from non-hydroelectric renewable sources are the United States, China, and Germany (EIA 2013).

The 150 MW Andasol Solar Power Station is a commercial parabolic trough solar thermal power plant, located in Spain. The Andasol plant uses tanks of molten salt to store solar energy so that it can continue generating electricity even when the sun isn't shining.

Renewable energy resources and significant opportunities for energy efficiency exist over wide geographical areas, in contrast to other energy sources, which are concentrated in a limited number of countries. Renewable energy replaces conventional fuels in four distinct areas: electricity generation, hot water/space heating, motor fuels, and rural (off-grid) energy services.

History

Prior to the development of coal in the mid 19th century, nearly all energy used was renewable.

Almost without a doubt the oldest known use of renewable energy was in the form of using wood (traditional biomass) to fuel fires. The discovery of how to make fire for the purpose of burning wood is regarded as one of humanity's most important advances. The use of wood as a fuel source for heating is much older than civilization and is assumed to have been used by Neanderthals. Although use of wood for fires has been dated to some 790,000 years ago, with evidence for controlled fire found at a Lower Paleolithic site in Israel, it possibly did not become commonplace until many hundreds of thousands of years later, sometime between 200,000 and 400,000 years ago (Hirst 2013; Roebroeks and Villa 2011; Twomey 2013).

Historically, it was limited in use only by the distribution of technology required to make a spark. Wood heat is still common throughout much of the world.

Probably the second oldest usage of renewable energy is harnessing the wind in order to drive ships over water. This practice can be traced back some 7000 years, to ships on the Nile.

Moving into the time of recorded history, the primary sources of traditional renewable energy were human labor, animal power, water power, wind, in grain crushing windmills, and firewood, a traditional biomass. A graph of energy use in the United States up until 1900 shows oil and natural gas with about the same importance in 1900 as wind and solar played in 2010.

By 1873, concerns of running out of coal prompted experiments with using solar energy. Development of solar engines continued until the outbreak of World War I. The importance of solar energy was recognized in a 1911 Scientific American article: "in the far distant future, natural fuels having been exhausted [solar power] will remain as the only means of existence of the human race".

The theory of peak oil was published in 1956. In the 1970s environmentalists promoted the development of renewable energy both as a replacement for the eventual depletion of oil, as well as for an escape from dependence on oil, and the first electricity generating wind turbines appeared. Solar had long been used for heating and cooling, but solar panels were too costly to build solar farms until 1980.

The categorization into renewable energy sources versus nonrenewable probably came into general use around 1973 to 1975, relagtive to work l of work on sustainability and energy security issues (Gritsevskyi 2008).

Historian Norman F. Cantor describes how in the late medieval period, coal was the new alternative fuel to save the society from overuse of the dominant fuel, wood (Cantor 1993):

"Europeans had lived in the midst of vast forests throughout the earlier medieval centuries. After 1250 they became so skilled at deforestation that by 1500 C.E. they were running short of wood for heating and cooking... By 1500 Europe was on the edge of a fuel and nutritional disaster, [from] which it was saved in the sixteenth century only by the burning of soft coal and the cultivation of potatoes and maize."

Coal would gain increase prominence during the industrial revolution in the late 18th century (Clark and Jacks 2007). While some historians consider coal only a "bit actor," other economic historians assert "coal was indeed at the heart of the Industrial Revolution," the "key transformative element of the Industrial Revolution," and that the "switch from a self-sustaining organic economy to a mineral resource depleting inorganic economy was central to the British Industrial Revolution" (Clark and Jacks 2007).

In the early 19th century, whale oil was the dominant form of lubrication and fuel for lamps in the early 19th century, but the depletion of the whale stocks by mid century caused whale oil prices to skyrocket setting the stage for the adoption of petroleum, which was first commercialized in Pennsylvania in 1859.

Already the foundation for alcohol to serve as an alternative to fossil fuels was laid in 1917, when Alexander Graham Bell advocated ethanol from corn, wheat, and other foods as an alternative to coal and oil, stating that the world was in measurable distance of depleting these fuels. For Bell, the problem requiring an alternative was lack of renewability of orthodox energy sources (Bell 1917).

Since the 1970s, Brazil has had an ethanol fuel program, which has allowed the country to become the world's second largest producer of ethanol (after the United States) and the world's largest exporter.

Mainstream renewable technologies

Wind power

The Shepherds Flat Wind Farm is a 845 megawatt (MW) wind farm in the U.S. state of Oregon.

Airflows can be used to run wind turbines. Modern utility-scale wind turbines range from around 600 kW to 5 MW of rated power, although turbines with rated output of 1.5–3 MW have become the most common for commercial use; the power available from the wind is a function of the cube of the wind speed, so as wind speed increases, power output increases dramatically up to the maximum output for the particular turbine. Areas where winds are stronger and more constant, such as offshore and high altitude sites, are preferred locations for wind farms. Typical capacity factors are 20-40%, with values at the upper end of the range in particularly favourable sites.

Globally, the long-term technical potential of wind energy is believed to be five times total current global energy production, or 40 times current electricity demand, assuming all practical barriers needed were overcome. This would require wind turbines to be installed over large areas, particularly in areas of higher wind resources, such as offshore. As offshore wind speeds average ~90% greater than that of land, so offshore resources can contribute substantially more energy than land stationed turbines.

Hydropower

See also: Hydroelectricity  and Hydropower

Energy in water can be harnessed and used. Since water is about 800 times denser than air, even a slow flowing stream of water, or moderate sea swell, can yield considerable amounts of energy. There are many forms of water energy:

• Hydroelectric energy is a term usually reserved for large-scale hydroelectric dams. The largest of which is the Three Gorges Dam in China and a smaller example is the Akosombo Dam in Ghana.
• Micro hydro systems are hydroelectric power installations that typically produce up to 100 kW of power. They are often used in water rich areas as a remote-area power supply (RAPS).
• Run-of-the-river hydroelectricity systems derive kinetic energy from rivers and oceans without the creation of a large reservoir.

Hydropower is produced in 150 countries, with the Asia-Pacific region generating 32 percent of global hydropower in 2010. China is the largest hydroelectricity producer, with 721 terawatt-hours of production in 2010, representing around 17 percent of domestic electricity use. There are now three hydroelectricity plants larger than 10 GW: the Three Gorges Dam in China, Itaipu Dam across the Brazil/Paraguay border, and Guri Dam in Venezuela.

Solar energy

Part of the 354 MW SEGS solar complex in northern San Bernardino County, California.

Photovoltaic SUDI shade is an autonomous and mobile station in France that provides energy for electric vehicles using solar energy.

Solar energy, radiant light and heat from the sun, is harnessed using a range of ever-evolving technologies such as solar heating, solar photovoltaics, solar thermal electricity, solar architecture and artificial photosynthesis.

Solar technologies are broadly characterized as either passive solar or active solar depending on the way they capture, convert and distribute solar energy. Active solar techniques include the use of photovoltaic panels and solar thermal collectors to harness the energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light dispersing properties, and designing spaces that naturally circulate air.

Solar power is the conversion of sunlight into electricity, either directly using photovoltaics (PV), or indirectly using concentrated solar power (CSP). Concentrated solar power systems use lenses or mirrors and tracking systems to focus a large area of sunlight into a small beam. Commercial concentrated solar power plants were first developed in the 1980s. Photovoltaics convert light into electric current using the photoelectric effect. Photovoltaics are an important and relatively inexpensive source of electrical energy where grid power is inconvenient, unreasonably expensive to connect, or simply unavailable. However, as the cost of solar electricity is falling, solar power is also increasingly being used even in grid-connected situations as a way to feed low-carbon energy into the grid.

In 2011, the International Energy Agency said that "the development of affordable, inexhaustible and clean solar energy technologies will have huge longer-term benefits. It will increase countries’ energy security through reliance on an indigenous, inexhaustible and mostly import-independent resource, enhance sustainability, reduce pollution, lower the costs of mitigating climate change, and keep fossil fuel prices lower than otherwise. These advantages are global. Hence the additional costs of the incentives for early deployment should be considered learning investments; they must be wisely spent and need to be widely shared".

Biomass

File:Rotor stump remover recover a tree roots for a biomass central..JPG

Rotor stump remover recover a tree roots for a biomass central, this is an example for eco-sostenible managing of forest.

Sugarcane plantation in Brazil (State of São Paulo), cane remains used to production of biomass energy.

A cogeneration plant in Metz, France. The station uses waste wood biomass as energy source, and provides electricity and heat for 30,000 dwellings.

Biomass is biological material derived from living, or recently living organisms. It most often refers to plants or plant-derived materials which are specifically called lignocellulosic biomass. As an energy source, biomass can either be used directly via combustion to produce heat, or indirectly after converting it to various forms of biofuel. Conversion of biomass to biofuel can be achieved by different methods which are broadly classified into: thermal, chemical, and biochemical methods.

Wood remains the largest biomass energy source today; examples include forest residues (such as dead trees, branches and tree stumps), yard clippings, wood chips and even municipal solid waste. In the second sense, biomass includes plant or animal matter that can be converted into fibers or other industrial chemicals, including biofuels. Industrial biomass can be grown from numerous types of plants, including miscanthus, switchgrass, hemp, corn, poplar, willow, sorghum, sugarcane, bamboo, and a variety of tree species, ranging from eucalyptus to oil palm (palm oil).

Plant energy is produced by crops specifically grown for use as fuel that offer high biomass output per hectare with low input energy. Some examples of these plants are wheat, which typically yield 7.5–8 tons (tonnes?) of grain per hectare, and straw, which typically yield 3.5–5 tons (tonnes?) per hectare in the UK. The grain can be used for liquid transportation fuels while the straw can be burned to produce heat or electricity. Plant biomass can also be degraded from cellulose to glucose through a series of chemical treatments, and the resulting sugar can then be used as a first generation biofuel.

Biomass can be converted to other usable forms of energy like methane gas or transportation fuels like ethanol and biodiesel. Rotting garbage, and agricultural and human waste, all release methane gas—also called "landfill gas" or "biogas." Crops, such as corn and sugar cane, can be fermented to produce the transportation fuel, ethanol. Biodiesel, another transportation fuel, can be produced from left-over food products like vegetable oils and animal fats. Also, biomass to liquids (BTLs) and cellulosic ethanol are still under research.

There is a great deal of research involving algal, or algae-derived, biomass due to the fact that it’s a non-food resource and can be produced at rates 5 to 10 times those of other types of land-based agriculture, such as corn and soy. Once harvested, it can be fermented to produce biofuels such as ethanol, butanol, and methane, as well as biodiesel and hydrogen.

The biomass used for electricity generation varies by region. Forest by-products, such as wood residues, are common in the United States. Agricultural waste is common in Mauritius (sugar cane residue) and Southeast Asia (rice husks). Animal husbandry residues, such as poultry litter, are common in the UK.

Biofuel

See also: Biofuel  and Sustainable biofuel

Biofuels include a wide range of fuels which are derived from biomass. The term covers solid biofuels, liquid biofuels, and gaseous biofuels. Liquid biofuels include bioalcohols, such as bioethanol, and oils, such as biodiesel. Gaseous biofuels include biogas, landfill gas and synthetic gas.

Bioethanol is an alcohol made by fermenting the sugar components of plant materials and it is made mostly from sugar and starch crops. These include maize, sugar cane and, more recently, sweet sorghum. The latter crop is particularly suitable for growing in dryland conditions, and is being investigated by ICRISAT for its potential to provide fuel, along with food and animal feed, in arid parts of Asia and Africa.

With advanced technology being developed, cellulosic biomass, such as trees and grasses, are also used as feedstocks for ethanol production. Ethanol can be used as a fuel for vehicles in its pure form, but it is usually used as a gasoline additive to increase octane and improve vehicle emissions. Bioethanol is widely used in the USA and in Brazil. The energy costs for producing bio-ethanol are almost equal to, the energy yields from bio-ethanol. However, according to the European Environment Agency, biofuels do not address global warming concerns.

Biodiesel is made from vegetable oils, animal fats or recycled greases. Biodiesel can be used as a fuel for vehicles in its pure form, but it is usually used as a diesel additive to reduce levels of particulates, carbon monoxide, and hydrocarbons from diesel-powered vehicles. Biodiesel is produced from oils or fats using transesterification and is the most common biofuel in Europe.

Biofuels provided 2.7% of the world's transport fuel in 2010.

Geothermal energy

Steam rising from the Nesjavellir Geothermal Power Station in Iceland.

Geothermal energy is from thermal energy generated and stored in the Earth. Thermal energy is the energy that determines the temperature of matter. Earth's geothermal energy originates from the original formation of the planet (20%) and from radioactive decay of minerals (80%). The geothermal gradient, which is the difference in temperature between the core of the planet and its surface, drives a continuous conduction of thermal energy in the form of heat from the core to the surface. The adjective geothermal originates from the Greek roots geo, meaning earth, and thermos, meaning heat.

The heat that is used for geothermal energy can be from deep within the Earth, all the way down to Earth’s core – 4,000 miles ( km) down. At the core, temperatures may reach over 9,000 °F (5,000 °C). Heat conducts from the core to surrounding rock. Extremely high temperature and pressure cause some rock to melt, which is commonly known as magma. Magma convects upward since it is lighter than the solid rock. This magma then heats rock and water in the crust, sometimes up to 700 °F (371 °C).

From hot springs, geothermal energy has been used for bathing since Paleolithic times and for space heating since ancient Roman times, but it is now better known for electricity generation.

Renewable energy commercialization

Growth of renewables

File:RE-CapChangeShare-Eng.png

Renewable power generation and capacity as a proportion of change in global power supply

Growth of wind power and photovoltaics

From the end of 2004, worldwide renewable energy capacity grew at rates of 10–60% annually for many technologies. For wind power and many other renewable technologies, growth accelerated in 2009 relative to the previous four years. More wind power capacity was added during 2009 than any other renewable technology. However, grid-connected PV increased the fastest of all renewables technologies, with a 60% annual average growth rate. In 2010, renewable power constituted about a third of the newly built power generation capacities. By 2014 the installed capacity of photovoltaics will likely exceed that of wind, but due to the lower capacity factor of solar, the energy generated from photovoltaics is not expected to exceed that of wind until 2015.

Selected renewable energy global indicators	2008	2009	2010	2011	2012
Investment in new renewable capacity (annual) (109 USD)	130	160	211	257	244
Renewables power capacity (existing) (GWe)	1,140	1,230	1,320	1,360	1,470
Hydropower capacity (existing) (GWe)	885	915	945	970	990
Wind power capacity (existing) (GWe)	121	159	198	238	283
Solar PV capacity (grid-connected) (GWe)	16	23	40	70	100
Solar hot water capacity (existing) (GWth)	130	160	185	232	255
Ethanol production (annual) (109 litres)	67	76	86	86	83
Biodiesel production (annual) (109 litres)	12	17.8	18.5	21.4	22.5
Countries with policy targets for renewable energy use	79	89	98	118	138

Projections vary, but scientists have advanced a plan to power 100% of the world's energy with wind, hydroelectric, and solar power by the year 2030.

According to a 2011 projection by the International Energy Agency, solar power generators may produce most of the world’s electricity within 50 years, dramatically reducing the emissions of greenhouse gases that harm the environment. Cedric Philibert, senior analyst in the renewable energy division at the IEA said: “Photovoltaic and solar-thermal plants may meet most of the world’s demand for electricity by 2060 — and half of all energy needs — with wind, hydropower and biomass plants supplying much of the remaining generation”. “Photovoltaic and concentrated solar power together can become the major source of electricity,” Philibert said.

Economic trends

File:EU-PV-LCOE-Projection.png

Cost of photovoltaics in the EU

File:US projected cost of wind power.png

The National Renewable Energy Laboratory projects that the levelized cost of wind power will decline 25% from 2012 to 2030.

Renewable energy technologies are getting cheaper, through technological change and through the benefits of mass production and market competition. A 2011 IEA report said: "A portfolio of renewable energy technologies is becoming cost-competitive in an increasingly broad range of circumstances, in some cases providing investment opportunities without the need for specific economic support," and added that "cost reductions in critical technologies, such as wind and solar, are set to continue."

Hydro-electricity and geothermal electricity produced at favourable sites are now the cheapest way to generate electricity. Renewable energy costs continue to drop, and the levelised cost of electricity (LCOE) is declining for wind power, solar photovoltaic (PV), concentrated solar power (CSP) and some biomass technologies.

Renewable energy is also the most economic solution for new grid-connected capacity in areas with good resources. As the cost of renewable power falls, the scope of economically viable applications increases. Renewable technologies are now often the most economic solution for new generating capacity. Where “oil-fired generation is the predominant power generation source (e.g. on islands, off-grid and in some countries) a lower-cost renewable solution almost always exists today”.

A series of studies by the US National Renewable Energy Laboratory modeled the "grid in the Western US under a number of different scenarios where intermittent renewables accounted for 33 percent of the total power." In the models, inefficiencies in cycling the fossil fuel plants to compensate for the variation in solar and wind energy resulted in an additional cost of "between $0.47 and $1.28 to each MegaWatt hour generated"; however, the savings in the cost of the fuels saved "adds up to $7 billion, meaning the added costs are, at most, two percent of the savings."

Hydroelectricity

Three Gorges Dam (left), Gezhouba Dam (right).

The Three Gorges Dam in Hubei, China, has the world's largest instantaneous generating capacity (22,500 MW), with the Itaipu Dam in Brazil/Paraguay in second place (14,000 MW). The Three Gorges Dam is operated jointly with the much smaller Gezhouba Dam (3,115 MW). As of 2012, the total generating capacity of this two-dam complex is 25,615 MW. In 2008, this complex generated 98 TWh of electricity (81 TWh from the Three Gorges Dam and 17 TWh from the Gezhouba Dam), which is 3% more power in one year than the 95 TWh generated by Itaipu in 2008.

Wind power development

File:GlobalWindPowerCumulativeCapacity.png

Wind power: worldwide installed capacity

File:Fentonwindpark1.jpg

Fenton Wind Farm at sunrise

Wind power is growing at over 20% annually, with a worldwide installed capacity of 238,000 MW at the end of 2011, and is widely used in Europe, Asia, and the United States. Several countries have achieved relatively high levels of wind power penetration, such as 21% of stationary electricity production in Denmark, 18% in Portugal, 16% in Spain, 14% in Ireland and 9% in Germany in 2010. As of 2011, 83 countries around the world are using wind power on a commercial basis.

Top 10 countries by nameplate windpower capacity
(2012 year-end)

Country	Windpower capacity (MW)	% world total
China	75,564ǂ	26.8
United States	60,007	21.2
Germany	31,332	11.1
Spain	22,796	8.1
India	18,421	6.5
United Kingdom	8,845	3.0
Italy	8,144	2.9
France	7,196ǂ	2.5
Canada	6,200	2.2
Portugal	4,525	1.6
(rest of world)	39,853	14.1
World total	282,482 MW	100%

As of 2012, the Alta Wind Energy Center (California, 1,020 MW) is the world's largest wind farm. The London Array (630 MW) is the largest offshore wind farm in the world. Phase 1 is complete, it is intended to introduce more turbines for Phase 2. The United Kingdom is the world's leading generator of offshore wind power, followed by Denmark.

There are many large wind farms under construction and these include Anholt Offshore Wind Farm (400 MW), BARD Offshore 1 (400 MW), Clyde Wind Farm (548 MW), Fântânele-Cogealac Wind Farm (600 MW), Greater Gabbard wind farm (500 MW), Lincs Wind Farm (270 MW), London Array (1000 MW), Lower Snake River Wind Project (343 MW), Macarthur Wind Farm (420 MW), Shepherds Flat Wind Farm (845 MW), and the Sheringham Shoal (317 MW).

Solar thermal

File:IvanpahRunning.JPG

Ivanpah Solar Electric Generating System with all three towers under load, Feb., 2014. Taken from I-15 in San Bernardino County, California. The Clark Mountain Range can be seen in the distance.

File:PS20andPS10.jpg

Solar Towers from left: PS10, PS20.

The United States conducted much early research in photovoltaics and concentrated solar power. The U.S. is among the top countries in the world in electricity generated by the Sun and several of the world's largest utility-scale installations are located in the desert Southwest. The oldest solar power plant in the world is the 354 MW SEGS thermal power plant, in California. The Ivanpah Solar Electric Generating System is a solar thermal power project in the California Mojave Desert, 40 miles (64 km) southwest of Las Vegas, with a gross capacity of 392 megawatts (MW). The 280 MW Solana Generating Station is a solar power plant near Gila Bend, Arizona, about 70 miles (110 km) southwest of Phoenix, completed in 2013. When commissioned it was the largest parabolic trough plant in the world and the first U.S. solar plant with molten salt thermal energy storage.

The solar thermal power industry is growing rapidly with 1.3 GW under construction in 2012 and more planned. Spain is the epicenter of solar thermal power development with 873 MW under construction, and a further 271 MW under development. In the United States, 5,600 MW of solar thermal power projects have been announced. In developing countries, three World Bank projects for integrated solar thermal/combined-cycle gas-turbine power plants in Egypt, Mexico, and Morocco have been approved.

Photovoltaic power stations

Photovoltaic power (GW)
2005	5.4
2006	7.0
2007	9.4
2008	15.7
2009	22.9
2010	39.7
2011	67.4
2012	100
Year end capacities

File:Giant photovoltaic array.jpg

Nellis Solar Power Plant, 14 MW power plant installed 2007 in Nevada, USA.

Solar photovoltaic cells (PV) convert sunlight into electricity and photovoltaic production has been increasing by an average of more than 20% each year since 2002, making it a fast-growing energy technology. While wind is often cited as the fastest growing energy source, photovoltaics since 2007 has been increasing at twice the rate of wind — an average of 63.6%/year, due to the reduction in cost. At the end of 2011 the photovoltaic (PV) capacity world-wide was 67.4 GW, a 69.8% annual increase. Top capacity countries were, in GW: Germany 24.7, Italy 12.8, Japan 4.7, Spain 4.4, the USA 4.4, and China 3.1.

Many solar photovoltaic power stations have been built, mainly in Europe. As of May 2012, the largest photovoltaic (PV) power plants in the world are the Agua Caliente Solar Project (USA, 247 MW), Charanka Solar Park (India, 214 MW), Golmud Solar Park (China, 200 MW), Perovo Solar Park (Ukraine, 100 MW), Sarnia Photovoltaic Power Plant (Canada, 97 MW), Brandenburg-Briest Solarpark (Germany, 91 MW), Solarpark Finow Tower (Germany, 84.7 MW), Montalto di Castro Photovoltaic Power Station (Italy, 84.2 MW), and the Eggebek Solar Park (Germany, 83.6 MW).

There are also many large plants under construction. The Desert Sunlight Solar Farm is a 550 MW solar power plant under construction in Riverside County, California, that will use thin-film solar photovoltaic modules made by First Solar. The Topaz Solar Farm is a 550 MW photovoltaic power plant, being built in San Luis Obispo County, California. The Blythe Solar Power Project is a 500 MW photovoltaic station under construction in Riverside County, California. The California Valley Solar Ranch (CVSR) is a 250 MW solar photovoltaic power plant, which is being built by SunPower in the Carrizo Plain, northeast of California Valley. The 230 MW Antelope Valley Solar Ranch is a First Solar photovoltaic project which is under construction in the Antelope Valley area of the Western Mojave Desert, and due to be completed in 2013.

Many of these plants are integrated with agriculture and some use tracking systems that follow the sun's daily path across the sky to generate more electricity than fixed-mounted systems. There are no fuel costs or emissions during operation of the power stations.

However, when it comes to renewable energy systems and PV, it is not just large systems that matter. Building-integrated photovoltaics or "onsite" PV systems use existing land and structures and generate power close to where it is consumed.

Biofuel development

Brazil has bioethanol made from sugarcane available throughout the country. Shown a typical Petrobras gas station at São Paulo with dual fuel service, marked A for alcohol (ethanol) and G for gasoline.

Biofuels provided 3% of the world's transport fuel in 2010. Mandates for blending biofuels exist in 31 countries at the national level and in 29 states/provinces. According to the International Energy Agency, biofuels have the potential to meet more than a quarter of world demand for transportation fuels by 2050.

Since the 1970s, Brazil has had an ethanol fuel program which has allowed the country to become the world's second largest producer of ethanol (after the United States) and the world's largest exporter. Brazil’s ethanol fuel program uses modern equipment and cheap sugarcane as feedstock, and the residual cane-waste (bagasse) is used to produce heat and power. There are no longer light vehicles in Brazil running on pure gasoline. By the end of 2008 there were 35,000 filling stations throughout Brazil with at least one ethanol pump.

Nearly all the gasoline sold in the United States today is mixed with 10% ethanol, a mix known as E10, and motor vehicle manufacturers already produce vehicles designed to run on much higher ethanol blends. Ford, Daimler AG, and GM are among the automobile companies that sell “flexible-fuel” cars, trucks, and minivans that can use gasoline and ethanol blends ranging from pure gasoline up to 85% ethanol (E85). By mid-2006, there were approximately 6 million E85-compatible vehicles on U.S. roads. The challenge is to expand the market for biofuels beyond the farm states where they have been most popular to date. Flex-fuel vehicles are assisting in this transition because they allow drivers to choose different fuels based on price and availability. The Energy Policy Act of 2005, which calls for Template:Convert/e9USgal of biofuels to be used annually by 2012, will also help to expand the market.

Geothermal development

File:West Ford Flat Geothermal Cooling Tower.JPG

The West Ford Flat power plant is one of 22 power plants at The Geysers.

Geothermal power is cost effective, reliable, sustainable, and environmentally friendly, but has historically been limited to areas near tectonic plate boundaries. Recent technological advances have dramatically expanded the range and size of viable resources, especially for applications such as home heating, opening a potential for widespread exploitation. Geothermal wells release greenhouse gases trapped deep within the earth, but these emissions are much lower per energy unit than those of fossil fuels. As a result, geothermal power has the potential to help mitigate global warming if widely deployed in place of fossil fuels.

The International Geothermal Association (IGA) has reported that 10,715 MW of geothermal power in 24 countries is online, which is expected to generate 67,246 GWh of electricity in 2010. This represents a 20% increase in geothermal power online capacity since 2005. IGA projects this will grow to 18,500 MW by 2015, due to the large number of projects presently under consideration, often in areas previously assumed to have little exploitable resource.

In 2010, the United States led the world in geothermal electricity production with 3,086 MW of installed capacity from 77 power plants; the largest group of geothermal power plants in the world is located at The Geysers, a geothermal field in California. The Philippines follows the US as the second highest producer of geothermal power in the world, with 1,904 MW of capacity online; geothermal power makes up approximately 18% of the country's electricity generation.

Developing countries

File:Solar-Panel-Cooker-in-front-of-hut.jpg

Solar cookers use sunlight as energy source for outdoor cooking.

File:Earthlife Africa brouchure.jpeg

Earthlife Africa promotional brochure.

Renewable energy can be particularly suitable for developing countries. In rural and remote areas, transmission and distribution of energy generated from fossil fuels can be difficult and expensive. Producing renewable energy locally can offer a viable alternative.

Technology advances are opening up a huge new market for solar power: the approximately 1.3 billion people around the world who don't have access to grid electricity. Even though they are typically very poor, these people have to pay far more for lighting than people in rich countries because they use inefficient kerosene lamps. Solar power costs half as much as lighting with kerosene. An estimated 3 million households get power from small solar PV systems. Kenya is the world leader in the number of solar power systems installed per capita. More than 30,000 very small solar panels, each producing 12 to 30 watts, are sold in Kenya annually. Some Small Island Developing States (SIDS) are also turning to solar power to reduce their costs and increase their sustainability.

Micro-hydro configured into mini-grids also provide power. Over 44 million households use biogas made in household-scale digesters for lighting and/or cooking, and more than 166 million households rely on a new generation of more-efficient biomass cookstoves. Clean liquid fuel sourced from renewable feedstocks are used for cooking and lighting in energy-poor areas of the developing world. Alcohol fuels (ethanol and methanol) can be produced sustainably from non-food sugary, starchy, and cellulostic feedstocks. Project Gaia, Inc. and CleanStar Mozambique are implementing clean cooking programs with liquid ethanol stoves in Ethiopia, Kenya, Nigeria and Mozambique.

Renewable energy projects in many developing countries have demonstrated that renewable energy can directly contribute to poverty reduction by providing the energy needed for creating businesses and employment. Renewable energy technologies can also make indirect contributions to alleviating poverty by providing energy for cooking, space heating, and lighting. Renewable energy can also contribute to education, by providing electricity to schools.

Industry and policy trends

File:Global-RE-Investment-VC-Eng.png

Global New Investments in Renewable Energy

U.S. President Barack Obama's American Recovery and Reinvestment Act of 2009 includes more than $70 billion in direct spending and tax credits for clean energy and associated transportation programs. Clean Edge suggests that the commercialization of clean energy will help countries around the world pull out of the current economic malaise. Leading renewable energy companies include First Solar, Gamesa, GE Energy, Q-Cells, Sharp Solar, Siemens, SunOpta, Suntech Power, and Vestas.

The military has also focused on the use of renewable fuels for military vehicles. Unlike fossil fuels, renewable fuels can be produced in any country, creating a strategic advantage. The US military has already committed itself to have 50% of its energy consumption come from alternative sources.

The International Renewable Energy Agency (IRENA) is an intergovernmental organization for promoting the adoption of renewable energy worldwide. It aims to provide concrete policy advice and facilitate capacity building and technology transfer. IRENA was formed on January 26, 2009, by 75 countries signing the charter of IRENA. As of March 2010, IRENA has 143 member states who all are considered as founding members, of which 14 have also ratified the statute.

As of 2011, 119 countries have some form of national renewable energy policy target or renewable support policy. National targets now exist in at least 98 countries. There is also a wide range of policies at state/provincial and local levels.

United Nations' Secretary-General Ban Ki-moon has said that renewable energy has the ability to lift the poorest nations to new levels of prosperity. In October 2011, he "announced the creation of a high-level group to drum up support for energy access, energy efficiency and greater use of renewable energy. The group is to be co-chaired by Kandeh Yumkella, the chair of UN Energy and director general of the UN Industrial Development Organisation, and Charles Holliday, chairman of Bank of America".

100% renewable energy

The incentive to use 100% renewable energy has been created by global warming and other ecological as well as economic concerns. Renewable energy use has grown much faster than anyone anticipated. The Intergovernmental Panel on Climate Change has said that there are few fundamental technological limits to integrating a portfolio of renewable energy technologies to meet most of total global energy demand. Mark Z. Jacobson says producing all new energy with wind power, solar power, and hydropower by 2030 is feasible and existing energy supply arrangements could be replaced by 2050. Barriers to implementing the renewable energy plan are seen to be "primarily social and political, not technological or economic". Jacobson says that energy costs with a wind, solar, water system should be similar to today's energy costs. Critics of the "100% renewable energy" approach include Vaclav Smil and James Hansen.

Emerging technologies

Other renewable energy technologies are still under development, and include cellulosic ethanol, hot-dry-rock geothermal power, and ocean energy. These technologies are not yet widely demonstrated or have limited commercialization. Many are on the horizon and may have potential comparable to other renewable energy technologies, but still depend on attracting sufficient attention and research, development and demonstration (RD&D) funding.

There are numerous organizations within the academic, federal, and commercial sectors conducting large scale advanced research in the field of renewable energy. This research spans several areas of focus across the renewable energy spectrum. Most of the research is targeted at improving efficiency and increasing overall energy yields. Multiple federally supported research organizations have focused on renewable energy in recent years. Two of the most prominent of these labs are Sandia National Laboratories and the National Renewable Energy Laboratory (NREL), both of which are funded by the United States Department of Energy and supported by various corporate partners. Sandia has a total budget of $2.4 billion while NREL has a budget of $375 million.

Cellulosic ethanol

Companies such as Iogen, POET, and Abengoa are building refineries that can process biomass and turn it into ethanol, while companies such as the Verenium Corporation, Novozymes, and Dyadic International are producing enzymes which could enable a cellulosic ethanol future. The shift from food crop feedstocks to waste residues and native grasses offers significant opportunities for a range of players, from farmers to biotechnology firms, and from project developers to investors.

Selected Commercial Cellulosic Ethanol Plants in the U.S. (Operational or under construction)

Company	Location	Feedstock
Abengoa Bioenergy	Hugoton, KS	Wheat straw
BlueFire Renewables	Irvine, CA	Multiple sources
Gulf Coast Energy	Mossy Head, FL	Wood waste
Mascoma	Lansing, MI	Wood
POET	Emmetsburg, IA	Corn cobs
SunOpta	Little Falls, MN	Wood chips
Xethanol	Auburndale, FL	Citrus peels

Carbon-neutral and negative fuels

Carbon-neutral fuels are synthetic fuels (including methane, gasoline, diesel fuel, jet fuel or ammonia) produced by hydrogenating waste carbon dioxide recycled from power plant flue-gas emissions, recovered from automotive exhaust gas, or derived from carbonic acid in seawater. Such fuels are considered carbon-neutral because they do not result in a net increase in atmospheric greenhouse gases. To the extent that synthetic fuels displace fossil fuels, or if they are produced from waste carbon or seawater carbonic acid, and their combustion is subject to carbon capture at the flue or exhaust pipe, they result in negative carbon dioxide emission and net carbon dioxide removal from the atmosphere, and thus constitute a form of greenhouse gas remediation.

Such renewable fuels alleviate the costs and dependency issues of imported fossil fuels without requiring either electrification of the vehicle fleet or conversion to hydrogen or other fuels, enabling continued compatible and affordable vehicles. Carbon-neutral fuels offer relatively low cost energy storage, alleviating the problems of wind and solar intermittency, and they enable distribution of wind, water, and solar power through existing natural gas pipelines. Nighttime wind power is considered the most economical form of electrical power with which to synthesize fuel, because the load curve for electricity peaks sharply during the warmest hours of the day, but wind tends to blow slightly more at night than during the day, so, the price of nighttime wind power is often much less expensive than any alternative. Germany has built a 250 kilowatt synthetic methane plant which they are scaling up to 10 megawatts.

The George Olah carbon dioxide recycling plant in Grindavík, Iceland has been producing 2 million liters of methanol transportation fuel per year from flue exhaust of the Svartsengi Power Station since 2011. It has the capacity to produce 5 million liters per year.

Marine energy

Rance, second largest tidal power station at 240 MW

Marine energy (also sometimes referred to as ocean energy) refers to the energy carried by ocean waves, tides, salinity, and ocean temperature differences. The movement of water in the world’s oceans creates a vast store of kinetic energy, or energy in motion. This energy can be harnessed to generate electricity to power homes, transport and industries.

The term marine energy encompasses both wave power — power from surface waves, and tidal power — obtained from the kinetic energy of large bodies of moving water. Offshore wind power is not a form of marine energy, as wind power is derived from the wind, even if the wind turbines are placed over water.

The oceans have a tremendous amount of energy and are close to many if not most concentrated populations. Ocean energy has the potential of providing a substantial amount of new renewable energy around the world.

Rank	Station	Country	Location	Capacity (MW)	Template:Tooltip
1	Sihwa Lake Tidal Power Station	South Korea	37°18′47″N 126°36′46″E	254
2	Rance Tidal Power Station	France	48°37′05″N 02°01′24″W	240
3	Annapolis Royal Generating Station	Canada	44°45′07″N 65°30′40″W	20
4	Jiangxia Tidal Power Station	China	28°20′34″N 121°14′25″E	3.9
5	Kislaya Guba Tidal Power Station	Russia	69°22′37″N 33°04′34″E	1.7

Enhanced geothermal systems

Enhanced geothermal system 1:Reservoir 2:Pump house 3:Heat exchanger 4:Turbine hall 5:Production well 6:Injection well 7:Hot water to district heating 8:Porous sediments 9:Observation well 10:Crystalline bedrock

Enhanced geothermal systems are a new type of geothermal power technologies that do not require natural convective hydrothermal resources. The vast majority of geothermal energy within drilling reach is in dry and non-porous rock. EGS technologies "enhance" and/or create geothermal resources in this "hot dry rock (HDR)" through hydraulic stimulation.

EGS / HDR technologies, like hydrothermal geothermal, are expected to be baseload resources which produce power 24 hours a day like a fossil plant. Distinct from hydrothermal, HDR / EGS may be feasible anywhere in the world, depending on the economic limits of drill depth. Good locations are over deep granite covered by a thick (3–5 km) layer of insulating sediments which slow heat loss. There are HDR and EGS systems currently being developed and tested in France, Australia, Japan, Germany, the U.S. and Switzerland. The largest EGS project in the world is a 25 megawatt demonstration plant currently being developed in the Cooper Basin, Australia. The Cooper Basin has the potential to generate 5,000–10,000 MW.

Experimental solar power

File:Concentració Fotovoltaica.jpg

Concentrating photovoltaics in Catalonia, Spain

Concentrated photovoltaics (CPV) systems employ sunlight concentrated onto photovoltaic surfaces for the purpose of electricity generation. Thermoelectric, or "thermovoltaic" devices convert a temperature difference between dissimilar materials into an electric current.

Artificial photosynthesis

Artificial photosynthesis uses techniques include nanotechnology to store solar electromagnetic energy in chemical bonds by splitting water to produce hydrogen and then using carbon dioxide to make methanol. Researchers in this field are striving to design molecular mimics of photosynthesis that utilize a wider region of the solar spectrum, employ catalytic systems made from abundant, inexpensive materials that are robust, readily repaired, non-toxic, stable in a variety of environmental conditions and perform more efficiently allowing a greater proportion of photon energy to end up in the storage compounds, i.e., carbohydrates (rather than building and sustaining living cells).

Renewable energy debate

Renewable electricity production, from sources such as wind power and solar power, is sometimes criticized for being variable or intermittent. However, the International Energy Agency has stated that deployment of renewable technologies usually increases the diversity of electricity sources and, through local generation, contributes to the flexibility of the system and its resistance to central shocks.

There have been "not in my back yard" (NIMBY) concerns relating to the visual and other impacts of some wind farms, with local residents sometimes fighting or blocking construction. In the USA, the Massachusetts Cape Wind project was delayed for years partly because of aesthetic concerns. However, residents in other areas have been more positive. According to a town councilor, the overwhelming majority of locals believe that the Ardrossan Wind Farm in Scotland has enhanced the area.

A recent UK Government document states that “projects are generally more likely to succeed if they have broad public support and the consent of local communities. This means giving communities both a say and a stake”. In countries such as Germany and Denmark many renewable projects are owned by communities, particularly through cooperative structures, and contribute significantly to overall levels of renewable energy deployment.

The market for renewable energy technologies has continued to grow. Climate change concerns, coupled with high oil prices, peak oil, and increasing government support, are driving increasing renewable energy legislation, incentives and commercialization. New government spending, regulation and policies helped the industry weather the 2009 economic crisis better than many other sectors.

References

ISBN links support NWE through referral fees

• Bloomberg. 2011. Global renewable energy market outlook: Executive summary. Bloomberg New Energy Finance November 16, 2011.

• Gritsevskyi, A. 2008. [Renewable vs. non-renewable energy sources, forms and technologies. 13th Meeting of the London Group on Environmental Accounting: September 29- October 3, 2008, Brussels, Belgium. Retrieved January 20, 2014.

• Jordan-Korte, K. 2011. Government Promotion of Renewable Energy Technologies: Policy Approaches and Market Development in Germany, the United States, and Japan. Springer. ISBN 9783834965875.

• International Energy Agency (IEA). 2014. FAQs: Renewable energy. International Energy Agency. Retrieved April 2, 2014.

• International Energy Agency (IEA). 2012. World Energy Outlook 2012: Chapter 7 - Renewable Energy Outlook. OECD Publishing. ISBN 9789264180840. Retrieved April 3, 2014.

• International Energy Agency (IEA). 2008. Renewables Information, 2008 edition. Paris: OECD Publishing.

• Renewable Energy Policy Network for the 21st Century (REN21). 2012. Renewables 2012: Global status report. REN21. Retrieved April 3, 2014.

• Renewable Energy Policy Network for the 21st Century (REN21). 2013. Renewables global futures report 2013. REN21. Retrieved April 3, 2014.

• United States Energy Information Administration (EIA). 2013. Energy in Brief: How much of our electricity is generated from renewable energy?. EIA. Retrieved April 3, 2014.

• United Nations Environment Programme (UNEP_. 2011. Renewable energy. UNEP. Retrieved April 2, 2014.

Bibliography

• Aitken, Donald W. (2010). Transitioning to a Renewable Energy Future, International Solar Energy Society, January, 54 pages.
• HM Treasury (2006). Stern Review on the Economics of Climate Change, 575 pages.
• International Council for Science (c2006). Discussion Paper by the Scientific and Technological Community for the 14th session of the United Nations Commission on Sustainable Development, 17 pages.
• International Energy Agency (2006). World Energy Outlook 2006: Summary and Conclusions, OECD, 11 pages.
• International Energy Agency (2007). Renewables in global energy supply: An IEA facts sheet, OECD, 34 pages.
• International Energy Agency (2008). Deploying Renewables: Principles for Effective Policies, OECD, 8 pages.
• International Energy Agency (2011). Deploying Renewables 2011: Best and Future Policy Practice, OECD.
• International Energy Agency (2011). Solar Energy Perspectives, OECD.
• Lovins, Amory (2011). Reinventing Fire: Bold Business Solutions for the New Energy Era, Chelsea Green Publishing, 334 pages.
• Makower, Joel, and Ron Pernick and Clint Wilder (2009). Clean Energy Trends 2009, Clean Edge.
• National Renewable Energy Laboratory (2006). Non-technical Barriers to Solar Energy Use: Review of Recent Literature, Technical Report, NREL/TP-520-40116, September, 30 pages.
• REN21 (2008). Renewables 2007 Global Status Report, Paris: REN21 Secretariat, 51 pages.
• REN21 (2009). Renewables Global Status Report: 2009 Update, Paris: REN21 Secretariat.
• REN21 (2010). Renewables 2010 Global Status Report, Paris: REN21 Secretariat, 78 pages.
• REN21 (2011). Renewables 2011: Global Status Report, Paris: REN21 Secretariat.
• REN21 (2012). Renewables 2012: Global Status Report, Paris: REN21 Secretariat.
• United Nations Environment Programme and New Energy Finance Ltd. (2007). Global Trends in Sustainable Energy Investment 2007: Analysis of Trends and Issues in the Financing of Renewable Energy and Energy Efficiency in OECD and Developing Countries, 52 pages.
• Worldwatch Institute and Center for American Progress (2006). American energy: The renewable path to energy security, 40 pages.

Credits

New World Encyclopedia writers and editors rewrote and completed the Wikipedia article in accordance with New World Encyclopedia standards. This article abides by terms of the Creative Commons CC-by-sa 3.0 License (CC-by-sa), which may be used and disseminated with proper attribution. Credit is due under the terms of this license that can reference both the New World Encyclopedia contributors and the selfless volunteer contributors of the Wikimedia Foundation. To cite this article click here for a list of acceptable citing formats.The history of earlier contributions by wikipedians is accessible to researchers here:

• Renewable_energy  ^history

The history of this article since it was imported to New World Encyclopedia:

• History of "Renewable energy"

Note: Some restrictions may apply to use of individual images which are separately licensed.