Ceramic

From New World Encyclopedia
This article is about ceramic materials. For the fine art, see Ceramics (art).
File:Shuttle STS-45.jpg
The space shuttle has a coat of ceramic tiles that protect it from the searing heat produced during reentry into the atmosphere.

The word ceramic is derived from the Greek word κεραμικος (keramikos), which means "having to do with pottery." The term covers inorganic, nonmetallic materials that have been hardened by baking at a high temperature. Up until the 1950s or so, the most important of these were the traditional clays, made into pottery, dinnerware, bricks, tiles, and the like. Since then, new materials called advanced ceramics have been prepared. Advanced ceramics are now being used in various fields, including aerospace, automotive, defense, environmental, fiber-optic, and medical technologies. Ceramic components are also used in cellular phones and personal computers. Each of NASA's space shuttles has a coating of roughly 34,000 ceramic tiles, which protect it from the searing heat (up to 2,300°F) produced during reentry into the atmosphere.

Recently, a composite material of ceramic and metal has been made, known as cermet.

Terminology

The American Society for Testing and Materials (ASTM) defines a ceramic item as "an article having a glazed or unglazed body of crystalline or partly crystalline structure, or of glass, which body is produced from essentially inorganic, nonmetallic substances and either is formed from a molten mass which solidifies on cooling, or is formed and simultaneously or subsequently matured by the action of the heat."

The word ceramic can be used as a noun that refers to the material or a product made from the material. Alternatively, ceramic may be used as an adjective that describes the material. In addition, ceramics is a singular noun referring to the art of making things out of ceramic materials.

Composition and classification

Traditional ceramics have mainly been silicate-based. Advanced ceramics are made from various other types of materials as well. Depending on their composition, they are classified as oxides, non-oxides, and composites.

  • Oxides: alumina, zirconia.
  • Non-oxides: carbides, borides, nitrides, silicides, and silicates.
  • Composites: particulate reinforced, combinations of oxides and non-oxides.

The materials in each of these classes can have unique properties.

Ceramic materials and their uses

  • Barium titanate (often mixed with strontium titanate), which has a property called ferroelectricity, is widely used in electromechanical devices known as transducers, as well as in ceramic capacitors and data storage elements.
  • Bismuth strontium calcium copper oxide is a high-temperature superconductor.
  • Boron carbide (B4C) is used in some types of personal, helicopter, and tank armor.
  • Boron nitride takes on physical forms that are similar to those of carbon: a graphite-like form used as a lubricant, and a diamond-like one used as an abrasive.
  • Bricks, which are mostly aluminum silicates, are used for construction.
  • Earthenware is often made from clay, quartz, and feldspar.
  • Ferrite (Fe3O4), which is ferrimagnetic, is used in the core of electrical transformers and in magnetic core memory.
  • Lead zirconate titanate is another ferroelectric material.
  • Magnesium diboride (MgB2) is an unconventional superconductor.
  • Porcelain, which usually contains the clay mineral kaolinite.
  • Silicon carbide (SiC) is used as an abrasive, a refractory material, and a "susceptor" that helps cook food in microwave furnaces.
  • Silicon nitride (Si3N4) is used as an abrasive powder.
  • Steatite (a type of soapstone) is used as an electrical insulator.
  • Uranium oxide (UO2) is used as fuel in nuclear reactors.
  • Yttrium barium copper oxide (YBa2Cu3O7-x) is another high-temperature superconductor.
  • Zinc oxide (ZnO) is a semiconductor and is used in the construction of varistors (a class of electrical resistors).
  • Zirconia, which in pure form undergoes many phase changes when heated, can be chemically "stabilized" in several different forms. Most ceramic knife blades are made of this material. Also, as it is a good conductor of oxygen ions, it could be useful in fuel cells.

Other applications

In the early 1980s, Toyota researched production of an adiabatic ceramic engine that could run at a temperature of over 6,000 °F (3,300 °C). Ceramic engines do not require a cooling system and hence allow a major weight reduction and therefore greater fuel efficiency. In a conventional metallic engine, much of the energy released by combustion of the fuel must be dissipated as waste heat, to prevent the metallic parts from melting.

Despite all these desirable properties, such engines are not being produced because it is difficult to manufacture ceramic parts with the requisite precision and durability. Imperfections in the ceramic material leads to cracks, and then to potentially dangerous equipment failure. Such engines are possible in laboratory settings, but mass-production is not yet feasible.

Efforts are being made to develop ceramic parts for gas turbine engines. Currently, even blades made of advanced metal alloys for the hot section of an engine require cooling and careful limiting of operating temperatures. Turbine engines made with ceramics could operate more efficiently, giving aircraft greater range and payload for a set amount of fuel.

Since the late 1990s, highly specialized ceramics, usually based on boron carbide, have been used in ballistic armored vests to repel large-caliber rifle fire. Such plates are commonly known as "small-arms protective inserts" (SAPI). Similar technology is used to armor the cockpits of some military airplanes because of the lightness of the material.

Recent advances in ceramics include bio-ceramics such as dental implants and synthetic bones. Hydroxyapatite, the natural mineral component of bone, has been synthesized from a number of biological and chemical sources and can be formed into ceramic materials. Orthopedic implants made from these materials bond readily to bone and other tissues in the body without rejection or inflammatory reactions.

Hydroxyapatite ceramics, however, are usually porous and lack mechanical strength. They are therefore used to coat metal orthopedic devices, to aid in forming a bond to bone, or as bone fillers. They are also used as fillers for orthopedic plastic screws to help reduce inflammation and increase absorption of the plastic materials. Work is being done to make strong, dense, nano-crystalline hydroxyapatite ceramics for orthopedic weight-bearing devices, replacing foreign metal and plastic materials. Ultimately, these ceramic materials, with the incorporation of proteins called collagens, may be used to make synthetic bones.

Properties of ceramics

Mechanical properties

Historically, ceramic products have been hard, porous, and brittle. The study of ceramics consists to a large extent of ways to accentuate the strengths and mitigate the limitations of the materials, as well as to develop new uses for these materials.

Ceramic materials can be crystalline or amorphous (lacking a definite structure). The atoms in these materials are bound together by ionic or covalent bonds. A material held together by either type of bond will tend to fracture before any plastic deformation takes place. Additionally, because these materials tend to be porous, the pores and other microscopic imperfections act as stress concentrators. As a result, ceramic materials are brittle.

Electrical properties

Semiconductivity

A number of ceramics are semiconductors. Most of these are oxides of transition metals, such as zinc oxide.

One common use of these semiconductors is for varistors. These are electrical resistors with the unusual property of "negative resistance." Once the voltage across the device reaches a certain threshold, a change in the electrical structure of the material causes its electrical resistance to drop from several megaohms down to a few hundred ohms. As a result, these materials can dissipate a lot of energy. In addition, they self reset—after the voltage across the device drops below a threshold, its resistance returns to being high.

This property makes them ideal for surge-protection applications. The best demonstration of their ability can be found in electrical substations, where they are employed to protect the infrastructure from lightning strikes. They have rapid response, require low maintenance, and do not appreciably degrade from use.

When various gases are passed over a polycrystalline ceramic, its electrical resistance changes. Based on this property, semiconducting ceramics are used to make inexpensive gas sensors.

Superconductivity

Under some conditions, such as extremely low temperatures, some ceramics exhibit superconductivity. The exact reason for this property is not known, but there are two major families of superconducting ceramics.

Ferroelectricity and subsets

Many ceramic materials exhibit the property of piezoelectricity—that is, they generate a voltage in response to applied mechanical stress (or pressure). This property links electrical and mechanical responses. These materials are used in digital watches and other electronics that rely on quartz resonators. In these devices, electricity is used to produce a mechanical motion (powering the device) and the mechanical motion is in turn used to generate an electrical signal. The unit of time measured is the natural interval required for electricity to be converted into mechanical energy and back again.

The piezoelectric effect is generally stronger in materials that also exhibit pyroelectricity—that is, materials that generate an electrical potential when they are heated or cooled. All pyroelectric materials are also piezoelectric. Thus, these materials can be used to interconvert between thermal, mechanical, and electrical energy. Such materials are used in motion sensors, where the tiny rise in temperature from a warm body entering a room is enough to produce a measurable voltage in the crystal.

Pyroelectricity, in turn, is observed most strongly in materials that also display the ferroelectric effect—materials in which a stable electric dipole can be oriented or reversed by applying an electrostatic field. Pyroelectricity is a necessary consequence of ferroelectricity. Such materials can therefore be used to store information in ferroelectric capacitors.

The most common examples of these materials are lead zirconate titanate and barium titanate. Besides the above-mentioned uses, the strong piezoelectric response of these materials is exploited in the design of high-frequency loudspeakers, transducers for sonar, and actuators for atomic force and scanning tunneling microscopes.

Positive thermal coefficient

Increases in temperature can cause grain boundaries to suddenly become insulating in some semiconducting ceramic materials, mostly mixtures of heavy metal titanates. The critical transition temperature can be adjusted over a wide range by variations in chemistry. In such materials, current will pass through the material until joule heating brings it to the transition temperature, at which point the circuit will be broken and current flow will cease. Such ceramics are used as self-controlled heating elements in, for example, the rear-window defrost circuits of most automobiles.

At the transition temperature, the material's dielectric response becomes theoretically infinite. While a lack of temperature control would rule out any practical use of the material near its critical temperature, the dielectric effect remains exceptionally strong even at much higher temperatures. Titanates with critical temperatures far below room temperature have become synonymous with "ceramic" in the context of ceramic capacitors for just this reason.

Processing of ceramic materials

Non-crystalline ceramics, being glasses, tend to be formed from melts. The glass is shaped when fully molten, by casting, or when in a state of toffee-like viscosity, by methods such as blowing to a mold. If the material becomes partly crystalline by later heat treatments, the resulting material is known as a glass-ceramic.

Crystalline ceramic materials are not amenable to a great range of processing. Methods for dealing with them tend to fall into one of two categories: (a) the ceramic is made in the desired shape by reaction in situ, or (b) powders are "formed" together into the desired shape and then sintered to produce a solid body. Ceramic forming techniques include shaping by hand, slip casting, tape casting (for making thin ceramic capacitors), injection molding, dry pressing, and other variations. (See details of these processes in the two books listed below.) Some methods use a hybrid of the two approaches.

In situ manufacturing

This method is most commonly used in producing cement and concrete. In this case, the dehydrated powders are mixed with water, which starts hydration reactions. As a result, long, interlocking crystals begin to form around the aggregates. Over time, a solid ceramic is produced.

The biggest problem with this method is that most reactions are so fast that good mixing is not possible, which tends to prevent large-scale construction. On the other hand, small-scale systems can be made by "deposition" techniques—various materials (reactants) are introduced above a substrate, and react to form the ceramic on the substrate. This process borrows techniques from the semiconductor industry, such as chemical vapor deposition, and is very useful to make ceramic coatings.

Sintering-based methods

The principles of sintering-based methods is simple. Once a roughly held together object (called a "green body") is made, it is baked in a kiln, where diffusion processes cause the green body to shrink. The pores in the object close up, resulting in a denser, stronger product. The firing is done at a temperature below the melting point of the ceramic. There is virtually always some porosity left, but the real advantage of this method is that the green body can be produced in any way imaginable, and still be sintered. This makes it a very versatile route.

There are thousands of possible refinements of this process. Some of the most common involve pressing the green body to give the densification a head start and reduce the sintering time needed. Sometimes organic binders such as polyvinyl alcohol are added to hold the green body together; these burn out during the firing (at 200-350°C). Sometimes organic lubricants are added during pressing to increase densification. It is not uncommon to combine these, and add binders and lubricants to a powder, then press. (The formulation of these organic chemical additives is an art in itself. This is particularly important in the manufacture of high performance ceramics such as those used by the billions for electronics, in capacitors, inductors, sensors, etc. The specialized formulations most commonly used in electronics are detailed in the book "Tape Casting," by R.E. Mistler, et al., Amer. Ceramic Soc. [Westerville, Ohio], 2000.) A comprehensive book on the subject, for mechanical as well as electronics applications, is "Organic Additives and Ceramic Processing," by D. J. Shanefield, Kluwer Publishers [Boston], 1996.

A slurry can be used in place of a powder, and then cast into a desired shape, dried and then sintered. Indeed, traditional pottery is done with this type of method, using a plastic mixture worked with the hands.

If a mixture of different materials is used together in a ceramic, the sintering temperature is sometimes above the melting point of one minor component - a liquid phase sintering. This results in shorter sintering times compared to solid state sintering.

References
ISBN links support NWE through referral fees

ASTM Standard C 242-01 “Standard Terminology of Ceramic Whitewares and Related Products”:

ASM Engineered Materials Handbook – Vol 4, Ceramics and Glass

Introduction to Ceramics; Kingery, Bowen, and Ulhmann

Modern Ceramic Engineering, Properties, Processing, and Use in Design; D. W. Richerson

Rice, Roy. Ceramic Fabrication Technology Marcel Dekker.

Ceramic Technology and Processing; A. G. King

"Discovering a Hidden Industry," The World & I, December 1998, p. 154. See www.worldandi.com.

See also

  • Ceramics (art)
  • Ceramic forming techniques
  • Porcelain
  • Pottery

External links

  • Advanced Ceramics – The Evolution, Classification, Properties, Production, Firing, Finishing and Design of Advanced Ceramics
  • Ceramics Directory – International Ceramics Directory of Companies and Organizations

Credits

New World Encyclopedia writers and editors rewrote and completed the Wikipedia article in accordance with New World Encyclopedia standards. This article abides by terms of the Creative Commons CC-by-sa 3.0 License (CC-by-sa), which may be used and disseminated with proper attribution. Credit is due under the terms of this license that can reference both the New World Encyclopedia contributors and the selfless volunteer contributors of the Wikimedia Foundation. To cite this article click here for a list of acceptable citing formats.The history of earlier contributions by wikipedians is accessible to researchers here:

The history of this article since it was imported to New World Encyclopedia:

Note: Some restrictions may apply to use of individual images which are separately licensed.